They are making several good points about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this article followed below.
Installing a tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably difficult project. If the old tub is conveniently accessible, the project can move immediately; if you need to open up a wall to eliminate the old bathtub as well as place the new tub, the job is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually qualified on your own for the task and fit attempting it. Instead of hiring a contractor to take control of a halfway-completed project, it is much better to take into consideration using one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This short article will assist you install a new tub in your restroom if you have actually currently bought a brand-new tub and don't require to alter the setup of your previous water system pipes.
Your devices as well as material list must comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly troublesome because of the limited accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Secure the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The former type should be connected to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Utilizing the two wood boards under its feet, position the bathtub in the required setting. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bath tub up until the spirit level checks out level.
To mount taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water system and examine all joints and brand-new pipework for leaks and tighten them if needed. Fill the tub and also examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the bathtub needs to wait until the tub has actually been used at the very least once as this will certainly settle it right into its last setting.
Planning for the Installation
To start with, the sustaining framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with wetness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealer can split relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for spending some time to read our post. Are you aware of somebody who is serious about How to Install a Bathtub? Be sure share it. Thanks a lot for going through it.
Click