Have you been hunting for critical information about How to Install a Bathtub?
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult project. If the old tub is conveniently obtainable, the task can move rapidly; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as embeded in the brand-new one. Make certain you have qualified yourself for the work and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Chances are you may need an expert plumber to make tube links.
This post will assist you mount a brand-new bath tub in your bathroom if you have actually already purchased a new tub as well as do not require to change the arrangement of your previous supply of water pipelines.
Your devices as well as product list need to make up the following:
Getting ready for the Setup
First of all, the supporting framework provided with the bath must be fitted (if needed) according to the producer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic due to the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, place the tub in the needed placement. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leaks as well as tighten them if needed. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used at least once as this will certainly settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in place between the faucet and also the sink. Protect the faucet in place with the manufacturer given backnut. As soon as the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the tap ends first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, leading to problems with wetness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split rather very early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about Installing A Bathtub, I was thinking sharing that segment was a good idea. Be sure to take the opportunity to distribute this post if you liked it. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule Appointment